Flexcharge PV7D 7 Amp Charge Controller for Photovoltaic Charging System

Description

Flexcharge PV7D 7 Amp Charge Controller for Photovaltaic Charging System
Flexcharge
7 Amp Charge Controller
for 12 Volt
Photovoltaic
Charging System
(Solar Only Applications)
Model: PV7D
US Manufactured Long Service Life and Performance History
We are a stocking Flexcharge dealer listed on SES Flexcharge dealer page
The following is copyrighted by SES Flexcharge.
The PV7D (for Dual and Single battery banks) is a cost effective shunting regulator designed for smaller 12V Solar Only applications with a maximum solar charging current of 7A. Special order 6V or 24V units.  These controllers are easily expandable to handle charging currents from 35 to 500A.  We have engineered these controllers to be extremely efficient, accurate, salt water spray resistant, and very small (1.5" x 2").  It is Ideal for use in a marine environment.
Use with Lead Acid AGM or Gel battery technologies.  Like the NC25A they also use only 4mA to operate the circuitry.  The PV7D controllers are not to be used with outboard motors or any generator based charging system.
For Lead Acid GEL, AGM, and Flooded cell Batteries. Do not use on Lithium batteries of any type.
Efficiency:
The PV7D are a all solid state design using the highest efficiency components. No heat sink is required on the PV7 because almost no heat that is generated in the high efficiency solid state components.
Dependability:
We took great care to design the PV7D for long term unattended operation; extensive transient voltage protection;  high steady state voltage protection (it is not affected by continuous charging input voltages up to 33V, the point where the transient voltage protection kicks in); fully sealed electronics for 100% humidity operation; etc...  The PV7D is designed for Install and Forget operation.
Simple to Use:
The PV7D includes an easy to read Charge Indicator.  The peak charge voltage is factory set so there are no user adjustments to contend with working with all lead acid battery types.  System wire connections are made by connecting to the controllers four wire pigtails, either by soldering or on a owner supplied terminal strip.
Easy Upgrades:
Upgrading the controller to regulate many hundreds amperes can be accomplished easily and  is relatively inexpensive.  Contact Flexcharge for details.
Energy State Tape Charging
This is the charging process used by all Flexcharge controllers.  It has many benefits including greatly reduced gassing during charging, and it allows for micro equalization of Lead acid as well as Gel battery technologies.
Features
:
Cost Effective charge controller for Photovoltaic charging sources.
Reverse polarity protected (Must have Fuse installed)
Precision Auto assembled using proven Surface Mount Technology
Hermetically sealed / potted electronics for use in high humidity and salt air environments.
High efficiency components allows packaging in a very small enclosure.
Safely Micro Equalizes Wet Cell Lead Acid and Sealed Gel battery technologies using the Energy State Taper Charge Process.
Expands easily into a high amperage controller.  Up to 500A charging capacity with a charging efficiency increase to 99.95%.
All Solid State Design for extra long life and dependability.
Factory Calibrated for charging lead acid Flooded cell, AGM, and GEL battery technologies.  No user adjustments.
Full 2 year repair or replacement warranty.
Charging Indicator displays when the controller is passing charging current to the battery.
Controller's circuitry eliminates back flow of current into solar panels during non charging periods.
OPERATING CHARACTERISTICS
:
12V Unit
Parameter
MIN.
TYP.
MAX.
INPUT VOLTAGE  (BAT or PV)
0V
-
30V
PROGRAMMED OVERSHOOT VOLTAGE  (MICRO - EQUALIZATION)
-
-
16.3V
CHARGING CURRENT
4mA
-
7A
CONTROLLER STANDBY CURRENT (NIGHT)
2mA
2.6mA
3mA
CONTROLLER STANDBY CURRENT (Charging)
4mA
5mA
6mA
CHARGE DISCONNECT VOLTAGE  (Regulation Voltage)
14.20
14.25V
14.30V
CHARGE RECONNECT VOLTAGE
13.50V
13.60V
13.70V
VOLTAGE DROP ACROSS CONTROLLER
0.2V
0.4V
0.56V
TRANSIENT SURGE SUPPRESSION
-
-
600W
HUMIDITY
5%
60%
100%
OPERATING TEMPERATURE
-40°C
25°C
60°C
MTBF  (Mean Time Between Failures)
-
-
30 Years
CASE SIZE
H=1.25" W=1.5" L=3.0"
Hurricane Wind Power
2019
Corporate America Today
2019 Best Off-Grid
Renewable Energy
Product Supplier - USA
UP TO 50% DISCOUNTS
TOP BRANDS
Payment
Shipping
Returns
Payment
Shipping
Returns
We accept payment by any of the following methods:
PayPal
Please pay as soon as possible after winning an auction, as that will allow us to post your item to you sooner!
We offer
Fast shipping
on all orders!
Your order will be dispatched within 1-3 working day of receiving payment (Monday-Friday) and you should expect to receive it one or two days after dispatch (for orders sent RM 1st Class).
In the very unlikely event that your item is lost or damaged during post, then WE are responsible and will issue either a full refund or replacement.
If you are not 100% satisfied with your purchase, you can return the product and get a full refund or exchange the product for another one, be it similar or not.
You can return a product for up to 14 days from the date you purchased it.
Any product you return must be in the same condition you received it and in the original packaging. Please keep the receipt.
See our other items
Thank you for visiting our Ebay store!
(Multiple Values) Flexcharge 7 Amp Charge Controller for 12 Volt Photovaltaic Charging System (Solar Only Applications) Model: PV7D US Manufactured Long Service Life and Performance History We are a stocking Flexcharge dealer listed here on SES Flexcharge's dealer page: [http://www.flexcharge.com/Where-to-buy.html] (http://www.flexcharge.com/Where-to-buy.html) The following is copyrighted by SES Flexcharge. The PV7D (for Dual and Single battery banks) is a cost effective shunting regulator designed for smaller 12V Solar Only applications with a maximum solar charging current of 7A. Special order 6V or 24V units. These controllers are easily expandable to handle charging currents from 35 to 500A. We have engineered these controllers to be extremely efficient, accurate, salt water spray resistant, and very small (1.5" x 2"). It is Ideal for use in a marine environment. Use with Lead Acid AGM or Gel battery technologies. Like the NC25A they also use only 4mA to operate the circuitry. The PV7D controllers are not to be used with outboard motors or any generator based charging system. For Lead Acid GEL, AGM, and Flooded cell Batteries. Do not use on Lithium batteries of any type Efficiency The PV7D are a all solid state design using the highest efficiency components. No heat sink is required on the PV7 because almost no heat that is generated in the high efficiency solid state components. Dependability We took great care to design the PV7D for long term unattended operation; extensive transient voltage protection; high steady state voltage protection (it is not affected by continuous charging input voltages up to 33V, the point where the transient voltage protection kicks in); fully sealed electronics for 100% humidity operation; etc... The PV7D is designed for Install and Forget operation. Simple to Use The PV7D includes an easy to read Charge Indicator. The peak charge voltage is factory set so there are no user adjustments to contend with working with all lead acid battery types. System wire connections are made by connecting to the controllers four wire pigtails, either by soldering or on a owner supplied terminal strip. Easy Upgrades Upgrading the controller to regulate many hundreds amperes can be accomplished easily and is relatively inexpensive. Contact Flexcharge for details. Energy State Tape Charging This is the charging process used by all Flexcharge controllers. It has many benefits including greatly reduced gassing during charging, and it allows for micro equalization of Lead acid as well as Gel battery technologies. Features ---Cost Effective charge controller for Photovoltaic charging sources. ---Reverse polarity protected (Must have Fuse installed) ---Precision Auto assembled using proven Surface Mount Technology ---Hermetically sealed / potted electronics for use in high humidity and salt air environments. ---High efficiency components allows packaging in a very small enclosure. ---Safely Micro Equalizes Wet Cell Lead Acid and Sealed Gel battery technologies using the Energy State Taper Charge Process. ---Expands easily into a high amperage controller. Up to 500A charging capacity with a charging efficiency increase to 99.95%. ---All Solid State Design for extra long life and dependability. ---Factory Calibrated for charging lead acid Flooded cell, AGM, and GEL battery technologies. No user adjustments. ---Full 2 year repair or replacement warranty. ---Charging Indicator displays when the controller is passing charging current to the battery. ---Controller's circuitry eliminates back flow of current into solar panels during non charging periods. OPERATING CHARACTERISTICS 12V Unit Parameter MIN. TYP. MAX. INPUT VOLTAGE (BAT or PV) 0V - 30V PROGRAMMED OVERSHOOT VOLTAGE (MICRO - EQUALIZATION) - - 16.3V CHARGING CURRENT 4mA - 7A CONTROLLER STANDBY CURRENT (NIGHT) 2mA 2.6mA 3mA CONTROLLER STANDBY CURRENT (Charging) 4mA 5mA 6mA CHARGE DISCONNECT VOLTAGE (Regulation Voltage) 14.20 14.25V 14.30V CHARGE RECONNECT VOLTAGE 13.50V 13.60V 13.70V VOLTAGE DROP ACROSS CONTROLLER 0.2V 0.4V 0.56V TRANSIENT SURGE SUPPRESSION - - 600W HUMIDITY 5% 60% 100% OPERATING TEMPERATURE -40°C 25°C 60°C MTBF (Mean Time Between Failures) - - 30 Years CASE SIZE H=1.25" W=1.5" L=3.0" [FREE! Sellers: Add a FREE map to your listings. FREE!] (http://newage.mystoremaps.com/echo/tagLine?sid=cea073c8-fc6f-494f-9ca5-610e8850a127&tid=2) Froo www.froo.com | Froo Cross Sell, Free Cross Sell, Cross promote, eBay Marketing, eBay listing Apps, eBay Apps, eBay Application
Flexcharge PV7D | 7 Amp Charge Controller for Photovaltaic Charging System
(Multiple Values)
Flexcharge
7 Amp Charge Controller
for 12 Volt Photovaltaic Charging System
(Solar Only Applications)
Model: PV7D
US Manufactured Long Service Life and Performance History
We are a stocking Flexcharge dealer listed here on SES Flexcharge's dealer page:
http://www.flexcharge.com/Where-to-buy.html
The following is copyrighted by SES Flexcharge.
The PV7D (for Dual and Single battery banks) is a cost effective shunting regulator designed for smaller 12V Solar Only applications with a maximum solar charging current of 7A. Special order 6V or 24V units.  These controllers are easily expandable to handle charging currents from 35 to 500A.  We have engineered these controllers to be extremely efficient, accurate, salt water spray resistant, and very small (1.5" x 2").  It is Ideal for use in a marine environment. Use with Lead Acid AGM or Gel battery technologies.  Like the NC25A they also use only 4mA to operate the circuitry.  The PV7D controllers are not to be used with outboard motors or any generator based charging system.
For Lead Acid GEL, AGM, and Flooded cell Batteries. Do not use on Lithium batteries of any type
Efficiency
The PV7D are a all solid state design using the highest efficiency components. No heat sink is required on the PV7 because almost no heat that is generated in the high efficiency solid state components.
Dependability
We took great care to design the PV7D for long term unattended operation; extensive transient voltage protection;  high steady state voltage protection (it is not affected by continuous charging input voltages up to 33V, the point where the transient voltage protection kicks in); fully sealed electronics for 100% humidity operation; etc...  The PV7D is designed for Install and Forget operation.
Simple to Use
The PV7D includes an easy to read Charge Indicator.  The peak charge voltage is factory set so there are no user adjustments to contend with working with all lead acid battery types.  System wire connections are made by connecting to the controllers four wire pigtails, either by soldering or on a owner supplied terminal strip.
Easy Upgrades
Upgrading the controller to regulate many hundreds amperes can be accomplished easily and  is relatively inexpensive.  Contact Flexcharge for details.
Energy State Tape Charging
This is the charging process used by all Flexcharge controllers.  It has many benefits including greatly reduced gassing during charging, and it allows for micro equalization of Lead acid as well as Gel battery technologies.
Features
Cost Effective charge controller for Photovoltaic charging sources.
Reverse polarity protected (Must have Fuse installed)
Precision Auto assembled using proven Surface Mount Technology
Hermetically sealed / potted electronics for use in high humidity and salt air environments.
High efficiency components allows packaging in a very small enclosure.
Safely Micro Equalizes Wet Cell Lead Acid and Sealed Gel battery technologies using the Energy State Taper Charge Process.
Expands easily into a high amperage controller.  Up to 500A charging capacity with a charging efficiency increase to 99.95%.
All Solid State Design for extra long life and dependability.
Factory Calibrated for charging lead acid Flooded cell, AGM, and GEL battery technologies.  No user adjustments.
Full 2 year repair or replacement warranty.
Charging Indicator displays when the controller is passing charging current to the battery.
Controller's circuitry eliminates back flow of current into solar panels during non charging periods.
OPERATING CHARACTERISTICS
12V Unit
Parameter
MIN.
TYP.
MAX.
INPUT VOLTAGE  (BAT or PV)
0V
-
30V
PROGRAMMED OVERSHOOT VOLTAGE  (MICRO - EQUALIZATION)
-
-
16.3V
CHARGING CURRENT
4mA
-
7A
CONTROLLER STANDBY CURRENT (NIGHT)
2mA
2.6mA
3mA
CONTROLLER STANDBY CURRENT (Charging)
4mA
5mA
6mA
CHARGE DISCONNECT VOLTAGE  (Regulation Voltage)
14.20
14.25V
14.30V
CHARGE RECONNECT VOLTAGE
13.50V
13.60V
13.70V
VOLTAGE DROP ACROSS CONTROLLER
0.2V
0.4V
0.56V
TRANSIENT SURGE SUPPRESSION
-
-
600W
HUMIDITY
5%
60%
100%
OPERATING TEMPERATURE
-40°C
25°C
60°C
MTBF  (Mean Time Between Failures)
-
-
30 Years
CASE SIZE
H=1.25" W=1.5" L=3.0"
FREE! Sellers: Add a FREE map to your listings. FREE!
Froo www.froo.com | Froo Cross Sell, Free Cross Sell, Cross promote, eBay Marketing, eBay listing Apps, eBay Apps, eBay Application
Hurricane Wind Power
2019
Corporate America Today
2019 Best Off-Grid
Renewable Energy
Product Supplier - USA
UP TO 50% DISCOUNTS
TOP BRANDS
See our other items
Payment
We accept payment by any of the following methods:
PayPal
Please pay as soon as possible after winning an auction, as that will allow us to post your item to you sooner!
Shipping
We offer
Fast shipping
on all orders!
Your order will be dispatched within 1-3 working day of receiving payment (Monday-Friday) and you should expect to receive it one or two days after dispatch (for orders sent RM 1st Class).
In the very unlikely event that your item is lost or damaged during post, then WE are responsible and will issue either a full refund or replacement.
Returns
If you are not 100% satisfied with your purchase, you can return the product and get a full refund or exchange the product for another one, be it similar or not.
You can return a product for up to 14 days from the date you purchased it.
Any product you return must be in the same condition you received it and in the original packaging. Please keep the receipt.
Thank you for visiting our Ebay store!
(Multiple Values)
Flexcharge
7 Amp Charge Controller
for 12 Volt Photovaltaic Charging System
(Solar Only Applications)
Model: PV7D
US Manufactured Long Service Life and Performance History
We are a stocking Flexcharge dealer listed here on SES Flexcharge's dealer page:
http://www.flexcharge.com/Where-to-buy.html
The following is copyrighted by SES Flexcharge.
The PV7D (for Dual and Single battery banks) is a cost effective shunting regulator designed for smaller 12V Solar Only applications with a maximum solar charging current of 7A. Special order 6V or 24V units.  These controllers are easily expandable to handle charging currents from 35 to 500A.  We have engineered these controllers to be extremely efficient, accurate, salt water spray resistant, and very small (1.5" x 2").  It is Ideal for use in a marine environment. Use with Lead Acid AGM or Gel battery technologies.  Like the NC25A they also use only 4mA to operate the circuitry.  The PV7D controllers are not to be used with outboard motors or any generator based charging system.
For Lead Acid GEL, AGM, and Flooded cell Batteries. Do not use on Lithium batteries of any type
Efficiency
The PV7D are a all solid state design using the highest efficiency components. No heat sink is required on the PV7 because almost no heat that is generated in the high efficiency solid state components.
Dependability
We took great care to design the PV7D for long term unattended operation; extensive transient voltage protection;  high steady state voltage protection (it is not affected by continuous charging input voltages up to 33V, the point where the transient voltage protection kicks in); fully sealed electronics for 100% humidity operation; etc...  The PV7D is designed for Install and Forget operation.
Simple to Use
The PV7D includes an easy to read Charge Indicator.  The peak charge voltage is factory set so there are no user adjustments to contend with working with all lead acid battery types.  System wire connections are made by connecting to the controllers four wire pigtails, either by soldering or on a owner supplied terminal strip.
Easy Upgrades
Upgrading the controller to regulate many hundreds amperes can be accomplished easily and  is relatively inexpensive.  Contact Flexcharge for details.
Energy State Tape Charging
This is the charging process used by all Flexcharge controllers.  It has many benefits including greatly reduced gassing during charging, and it allows for micro equalization of Lead acid as well as Gel battery technologies.
Features
Cost Effective charge controller for Photovoltaic charging sources.
Reverse polarity protected (Must have Fuse installed)
Precision Auto assembled using proven Surface Mount Technology
Hermetically sealed / potted electronics for use in high humidity and salt air environments.
High efficiency components allows packaging in a very small enclosure.
Safely Micro Equalizes Wet Cell Lead Acid and Sealed Gel battery technologies using the Energy State Taper Charge Process.
Expands easily into a high amperage controller.  Up to 500A charging capacity with a charging efficiency increase to 99.95%.
All Solid State Design for extra long life and dependability.
Factory Calibrated for charging lead acid Flooded cell, AGM, and GEL battery technologies.  No user adjustments.
Full 2 year repair or replacement warranty.
Charging Indicator displays when the controller is passing charging current to the battery.
Controller's circuitry eliminates back flow of current into solar panels during non charging periods.
OPERATING CHARACTERISTICS
12V Unit
Parameter
MIN.
TYP.
MAX.
INPUT VOLTAGE  (BAT or PV)
0V
-
30V
PROGRAMMED OVERSHOOT VOLTAGE  (MICRO - EQUALIZATION)
-
-
16.3V
CHARGING CURRENT
4mA
-
7A
CONTROLLER STANDBY CURRENT (NIGHT)
2mA
2.6mA
3mA
CONTROLLER STANDBY CURRENT (Charging)
4mA
5mA
6mA
CHARGE DISCONNECT VOLTAGE  (Regulation Voltage)
14.20
14.25V
14.30V
CHARGE RECONNECT VOLTAGE
13.50V
13.60V
13.70V
VOLTAGE DROP ACROSS CONTROLLER
0.2V
0.4V
0.56V
TRANSIENT SURGE SUPPRESSION
-
-
600W
HUMIDITY
5%
60%
100%
OPERATING TEMPERATURE
-40°C
25°C
60°C
MTBF  (Mean Time Between Failures)
-
-
30 Years
CASE SIZE
H=1.25" W=1.5" L=3.0"
FREE! Sellers: Add a FREE map to your listings. FREE!
Froo www.froo.com | Froo Cross Sell, Free Cross Sell, Cross promote, eBay Marketing, eBay listing Apps, eBay Apps, eBay Application